OPERATOR’S MANUAL
Expand-it™
Blower Attachment
UT15519E
Your Expand-it™ Blower Attachment has been engineered and manufactured to a high standard for dependability, ease of
operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
Thank you for buying an Expand-it™ Product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
GENERAL SAFETY RULES
Do not operate in poor lighting.
WARNING:
Read and understand all instructions. Failure to fol-
low all instructions listed below, may result in electric
shock, fire, and/or serious personal injury.
Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enables better control
of the tool in unexpected situations.
Keep all parts of your body away from any moving part.
Do not touch areas around the muffler or cylinder of the
power head. These parts get hot from operation. Failure
to heed this warning could result in possible serious
personal injury.
SAVE THESE INSTRUCTIONS
Read these instructions and the instructions for the power
head thoroughly before using the blower attachment.
Know the tool. Read and understand the operator’s
manual and observe the warnings and instruction labels
affixed to the tool.
Always stop the engine and remove the spark plug wire
before making any adjustments or repairs.
Inspect unit before each use for loose fasteners and dam-
aged or missing parts. Correct before using the blower
attachment. Failure to do so can cause serious injury.
Do not allow children or untrained individuals to use this
unit.
Wear safety glasses or goggles that are marked to comply
with ANSI Z87.1 standards and hearing protection when
operating this unit.
Use only identical manufacturer’s replacement parts and
accessories. Use of any other parts may create a hazard
or cause product damage.
Wear heavy long pants, boots, and gloves. Do not wear
loose fitting clothing, short pants, jewelry of any kind, or
go barefoot.
Do not, under any circumstance, use any attachment or
accessory on this product, which was not provided with
the product, or identified as appropriate for use with this
product in the operator’s manual.
Secure long hair so it is above shoulder level to prevent
entanglement in any moving parts.
Avoid dangerous environments. Do not use the attach-
Keep all bystanders, children, and pets at least 50 ft.
ment in damp or wet locations. Do not use in rain.
away.
Use the right attachment. Do not use attachment for any
Stay alert, watch what you are doing, and use common
sense when operating a power tool. Do not use tool while
tired or under the influence of drugs, alcohol, or medica-
tion. A moment of inattention while operating power tools
may result in serious personal injury.
job except that for which it is intended.
SPECIFIC SAFETY RULES
Always stay clear of air intake while blower is running.
Wear a face filter mask in dusty conditions to reduce the
risk of injury associated with the inhalation of dust.
Do not point blower in direction of people or pets.
Check the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.
To prevent electrical shock or serious personal injury, do
not use this product with any AC power head.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool.
If you loan someone this tool, loan them these in-
structions also to prevent misuse of the product and
possible injury.
To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
Never direct air blast towards any persons, animals,
plants, or delicate objects.
Keep air intake clear of debris.
3
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
EXPLANATION
Safety Alert Symbol
Precautions that involve your safety.
To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Read The Operator’s Manual
Eye and Hearing Protection
Keep Bystanders Away
Long Hair
Wear eye and hearing protection when operating this equipment.
Keep all bystanders at least 50 ft. away.
Failure to keep long hair away from the air inlet could result in personal
injury.
Failure to keep loose clothing from being drawn into air intake could result
in personal injury.
Loose Clothing
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will result in death
or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could result in death
or serious injury.
WARNING:
CAUTION:
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in minor
or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing, use
only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. If you do not understand the
warnings and instructions in the operator’s manual, do not use
this product. Call Expand-it customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in
severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with
side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use over eye-
glasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with
ANSI Z87.1.
SAVE THESE INSTRUCTIONS
4
FEATURES
PRODUCT SPECIFICATIONS
Weight ............................................................................................................................................................................4 lbs.
Air Velocity:
MPH...............................................................................................................................................................................150
CFM ...............................................................................................................................................................................279
END CAP
BLOWER ATTACHMENT SHAFT
AIR INTAKE
BLOWER HOUSING
AIR OUTLET
Fig. 1
KNOW YOUR BLOWER ATTACHMENT
See Figure 1.
The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well
as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features
and safety rules.
5
ASSEMBLY
UNPACKING
This product requires assembly.
POWER HEAD SHAFT
Carefully remove the items from the box. Make sure that
all items listed in the packing list are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-800-242-4672 for assistance.
GUIDE RECESS
COUPLER
KNOB
PACKING LIST
Expand-it™ Blower Attachment
Hanger Cap
POSITIONING
HOLE
Operator’s Manual
WARNING:
BLOWER
ATTACHMENT
If any parts are damaged or missing, do not operate
this tool until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
Fig. 2
Push in the button located on the blower attachment.
Align the button with the guide recess on the power head
coupler and slide the two shafts together. Rotate attach-
ment shaft until button locks into the positioning hole.
WARNING:
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
NOTE: If the button does not release completely in the
positioning hole, the shaft is not locked into place. Slightly
rotate from side to side until the button is locked into
place.
Tighten the knob securely.
JOINING THE POWER HEAD TO THE
BLOWER ATTACHMENT
See Figure 2.
WARNING:
Be certain the knob is fully tightened before operating
equipment. Check it periodically for tightness during use
to avoid serious injury.
WARNING:
Never attach or adjust any attachment while power head
is running. Failure to stop the engine may cause serious
personal injury.
REMOVING THE ATTACHMENT FROM THE
POWER HEAD
For removing or changing the attachment:
The blower attachment connects to the power head by
means of a coupler device.
Loosen the knob.
Loosen the knob on the coupler of the power head shaft
Push in the button and twist the shafts to remove and
and remove the end cap from the attachment shaft.
separate ends.
6
OPERATION
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Fig. 3
Clearing leaves and other debris from your lawn
The blower produces a strong air blast when operated at
full speed and the air force is directly controlled by the
engine speed.
Keeping decks and driveways free from leaves and pine
needles
In many situations it is not necessary to use the full power
of the blower; in fact it is not advisable in some applica-
tions. When using the blower in tight quarters, such as
corners of patios and garages, full power is not usually
required. A somewhat slower speed will do the same job
effectively without the turbulence created by full power
operation. This turbulence only carries the blown material
back into the corner and produces floating dust.
USING THE BLOWER ATTACHMENT
See Figure 3.
When using the blower attachment, hold the unit with your
right hand on the rear handle and your left hand on the front
handle. Keep a firm grip with both hands while in operation.
The blower should be held at a comfortable position with
the rear handle about hip height.
NOTE: Carry the unit slightly above ground level. Do not
drag or push it along on the ground as the housing will
wear quickly.
To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the center
of a pile.
You will find that it is no longer necessary to move objects
to effectively clean around them. A simple blast from the
blower will move debris from those difficult to reach and
often impossible to clean areas.
OPERATING TIPS
So that you may become accustomed to the blower
operation, start the engine and let it warm up. At idle,
you will find that no air is moving because the clutch is
disengaged. As you gradually increase the engine speed
to full throttle, you will find that the air force increases
also.
The ground level air blast is ideal for practically all sweep-
ing jobs.
7
MAINTENANCE
ATTACHING THE STORAGE HANGER
See Figure 4.
WARNING:
There are two ways to hang the attachment for storage.
To use the hanger cap, push in the button and place the
hanger cap over end of the lower end attachment shaft.
Slightly rotate the cap from side to side until the button
locks into place.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
The secondary hole in the attachment shaft can be used
WARNING:
for hanging purposes as well.
Always wear safety goggles or safety glasses with side
shields during tool operation. If operation is dusty, also
wear a dust mask.
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
HANGER
CAP
HOLE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
SECONDARY
HOLE
BUTTON
Fig. 4
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or de-
stroy plastic which may result in serious personal injury.
Youcanoftenmakeadjustmentsandrepairsdescribedhere.
For other repairs, have the tool serviced by an authorized
service dealer.
8
EXPLODED VIEW AND PARTS LIST
17
2
1
9
8
14
Key
No.
Part
No.
Description
Qty.
1
2
3
4
5
6
7
8
9
308737001
940657007
518385001
518386001
638264001
308497001
308499001
660902001
678263001
Drive Shaft Housing Assembly (Incl. Key No. 2) ............ 1
Warning Label ................................................................1
Clamp ............................................................................1
Upper Housing...............................................................1
Adapter-arbor ................................................................1
Bushing Assembly..........................................................1
Shaft Arbor.....................................................................1
* Screw (M5 x 6 mm) ........................................................1
Lock Washer ..................................................................1
Impeller Assembly..........................................................1
C-ring .............................................................................1
* Screw (M4.2 x 19 mm Pan Hd.) ..................................... 5
Lower Housing...............................................................1
* Screw (M4.8 x 26 mm T.F.).............................................3
Lower Housing Guard ....................................................1
* Screw (M4.2 x 12 mm) ..................................................2
Hanger Cap....................................................................1
Washer ...........................................................................1
Expand-It Label..............................................................1
Operator’s Manual..........................................................1
Repair Sheet
3
19
4
5
10 308498001
11 678283001
12 660895001
13 518389001
14 660896001
15 678374001
16 660676001
17 518019001
18 678282001
19 940726002
983000932
6
7
10
13
18
11
983000932R
15
16
12
* STANDARD HARDWARE ITEM — MAY BE PURCHASED LOCALLY
9
NOTES
10
WARRANTY
In addition, this warranty does not cover:
LIMITED WARRANTY STATEMENT
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
Techtronic Industries North America, Inc., warrants to the
original retail purchaser that this EXPAND-IT brand product
is free from defect in material and workmanship and agrees
to repair or replace, at Techtronic Industries North America,
Inc.’s discretion, any defective product free of charge within
these time periods from the date of purchase.
B. Wear items – Bump Knobs, Outer Spools, Cutting Lines,
Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts,
Tines,FeltWashers,HitchPins,MulchingBlades,Blower
Fans, Blower and Vacuum Tubes, Vacuum Bags and
Straps, Guide Bars, Saw Chains
One year for the following units: all Yard Broom, Trimlite,
and Bandit models;
Techtronic Industries North America, Inc., reserves the right
to change or improve the design of any EXPAND-IT brand
product without assuming any obligation to modify any
product previously manufactured.
Two years if the product is used for personal, family or
household use;
90daysifusedforanyotherpurpose,suchascommercial
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN THEIR
ENTIRETYAFTERTHEEXPIRATIONOFTHEAPPROPRIATE
TWO-YEAR, ONE-YEAR, OR NINETY-DAY WARRANTY
PERIOD. TECHTRONIC INDUSTRIES NORTH AMERICA,
INC.’S OBLIGATION UNDER THIS WARRANTY IS
STRICTLYANDEXCLUSIVELYLIMITEDTOTHEREPAIROR
REPLACEMENTOFDEFECTIVEPARTSANDTECHTRONIC
INDUSTRIESNORTHAMERICA,INC., DOESNOTASSUME
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. TECHTRONIC INDUSTRIES NORTH AMERICA,
INC., ASSUMES NO RESPONSIBILITY FOR INCIDENTAL,
CONSEQUENTIAL,OROTHERDAMAGESINCLUDING,BUT
NOTLIMITEDTO,EXPENSEOFRETURNINGTHEPRODUCT
TO AN EXPAND-IT AUTHORIZED SERVICE CENTER AND
EXPENSE OF DELIVERING IT BACK TO THE OWNER,
MECHANIC’S TRAVEL TIME, TELEPHONE OR TELEGRAM
CHARGES,RENTALOFALIKEPRODUCTDURINGTHETIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS OF
REVENUE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME,ORINCONVENIENCE.SOMESTATESDONOTALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIALDAMAGES,SOTHEABOVELIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU.
or rental.
Thiswarrantyextendstotheoriginalretailpurchaseronlyand
commences on the date of the original retail purchase.
Any part of the product found in the reasonable judgment
of Techtronic Industries North America, Inc., to be defective
in material or workmanship will be repaired or replaced
withoutchargeforpartsandlaborbyanExpand-itauthorized
service center.
The product, including any defective part, must be returned
toanExpand-itauthorizedservicecenterwithinthewarranty
period. The expense of delivering the product to the service
center for warranty work and the expense of returning it
back to the owner after repair or replacement will be paid
by the owner. Techtronic Industries North America, Inc.’s
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach of
warranty shall be cause for cancellation or rescission of the
contract of sale of any EXPAND-IT brand product. Proof of
purchase will be required by the dealer to substantiate any
warranty claim. All warranty work must be performed by an
Expand-it authorized service center.
This warranty is limited to ninety (90) days from the date of
original retail purchase for any EXPAND-IT brand product
that is used for rental or commercial purposes, or any other
income-producing purpose.
This warranty does not cover any product that has been
subject to misuse, neglect, negligence, or accident, or that
has been operated in any way contrary to the operating
instructions as specified in this operator’s manual. This
warranty does not apply to any damage to the product that
is the result of improper maintenance or to any product that
has been altered or modified. The warranty does not extend
to repairs made necessary by normal wear or by the use of
parts or accessories which are either incompatible with the
EXPAND-IT brand product or adversely affect its operation,
performance, or durability.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all EXPAND-IT brand products
manufactured by or for Techtronic Industries North America,
Inc., and sold in the United States and Canada.
To locate your nearest Expand-it authorized service center,
dial 1-800-242-4672.
11
OPERATOR’S MANUAL
Expand-it™
Blower Attachment
UT15519E
SERVICE
Forpartsorservice, contactyournearestExpand-it™ authorizedservicecenter. Besuretoprovideall
relevant information when you call or visit. For the location of the authorized service center nearest
REPAIR PARTS
The model number of this tool is found on a plate or label attached to the housing. Please record
the serial number in the space provided below.
UT15519E
MODEL NUMBER
SERIAL NUMBER
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
1428 Pearman Dairy Road
Anderson, SC 29625
Phone 1-800-242-4672
983000-932
2-27-06 (REV:00)
|